Диагностика кодов неисправностей двигателя Н4М Принятые сокращения: ABS: антиблокировочная тормозная система AC: кондиционер AFS: послепродажное обслуживание AS: система подачи воздуха BCM: ЦБКЭ CAN: шина обмена данными CB: сгорание CC: круиз-контроль CCSL: круиз-контроль / ограничитель скорости CO2: химический символ диоксида углерода DC: ездовой цикл DED: диагностики досье пользователя deg C: градусов по Цельсию DID: идентификатор данных DTC: данные кода неисправности ECM: Модуль управления двигателем ECU: Блок управления электронный EEPROM: электрическое репрограммируемое постоянное запоминающее устройство EGR: рециркуляция отработавших газов EOBD: европейская система бортовой диагностики ESP: электронная программа стабилизации ETC: электронный компонент дросселя ЕV: электроклапан HC: химический символ несгоревшего топлива HP: высокое давление IMV: впускной дозирующий клапан (= VCV) IT: на входе / потребление дросселя lokal ID: локальный идентификатор LSB: последний значащий бит MAF: массовый расход воздуха MAP: давление воздуха в коллекторе MAX: максимальная MIL: лампа индикации неисправности MIN: минимальный MSB: старший бит NOK: не в порядке NOx: химический символ оксида азота NRC: не перезаписываемый код O2: химический символ для кислорода OC: разомкнутая цепь OWE: оценка износа масла PWM: режим широтно-импульсной RAM: оперативное запоминающее устройство RPM: вращение в минуту RR: регулирование холостого хода SC: короткое замыкание SCB: короткое замыкание на напряжение аккумулятора SCG: короткое замыкание на землю SCW: короткое замыкание на источник питания SL: ограничитель скорости SM: скорость управление TDC: верхняя мертвая точка TQ: крутящий момент Vdiag: диагностики номер версии для послепродажного обслуживания Verlog: иммобилайзер VF: функции автомобиля VIN: идентификационный номер транспортного средства VVT: газораспределение Коды неисправностей двигателя Н4М
P0010 - Электромагнитный клапан впускного распределительного изменения фаз газораспределения P0011 - Функция управления впускного распределительного изменения фаз газораспределения P0016 - Положение распределительного вала - корреляция впускного распределительного положения P0105 - Датчик абсолютного давления P0106 - Функция абсолютного давления P0115 -Датчик температуры охлаждающей жидкости двигателя P0120 - Датчик положения дроссельной заслонки P0130 - Управляющий датчик кислорода P0133 - УДК медленный отклик в цепи P0135 - Нагреватель УДК P0136 - Диагностический датчик кислорода P0140 - ДДК активность цепи P0141 - Нагреватель ДДК P0170 - Топливо P0201 - Цепь форсунки - цилиндр 1 P0202 - Цепь форсунки - цилиндр 2 P0203 - Цепь форсунки - цилиндр 3 P0204 - Цепь форсунки - цилиндр 4 P0217 - Температура охлаждающей жидкости двигателя P0220 - Датчик положения дроссельной заслонки - трек 2 P0225 - Датчик положения педали акселератора - трек 1 P0226 - Датчик положения педали акселератора P025A - Модуль цепи управления бензонасосом P0300 - Обнаружены случайные / множественные пропуски воспламенения P0301 - Обнаружены пропуски воспламенения - цилиндр 1 P0302 - Обнаружены пропуски воспламенения - цилиндр 2 P0303 - Обнаружены пропуски воспламенения - цилиндр 3 P0304 - Обнаружены пропуски воспламенения - цилиндр 4 P0313 - Обнаружены пропуски воспламенения - отключена топливоподача P0315 - Система положения коленчатого вала вариатора не обучена P0325 - Датчик детонации P0335 - Датчик положения коленчатого вала Расшифровка P0010 – Электромагнитный клапан впускного распределительного изменения фаз газораспределения DTC | 0010h | Intake Camshaft Variable Valve Timing Solenoid Valve | Fault Type | Description | ABC Type | 13h | Circuit Open | Vbx_clf | 11h | Circuit Short to Ground | Vbx_clf | 12h | Circuit Short to Battery | Vbx_clf | Detection Conditions for Bit 4 (readiness) | 13h | Key on AND battery voltage between 10V and 16V | 11h | Key on AND battery voltage between 10V and 16V AND command OFF (PWM Command of inlet VVT < C_VVTPWM_DIAG_MAX_SCG) | 12h | Key on AND battery voltage between10V and 16V | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 13h | Hardware detection of VVT command Open Circuit | 1000 ms | 2000 ms | 11h | Hardware detection of VVT command Short Circuit to Ground | 1000 ms | 2000 ms | 12h | Hardware detection of VVT command Short Circuit to Bat-tery | 1000 ms | 2000 ms | Specific Snapshot | $2007 - Oil temperature - engine | $2010 - Engine status | $2030 - Intake camshaft phaser position setpoint | $2031 - Intake camshaft phaser position | $2033 - Intake camshaft phaser PWM command |
P0011 – Функция управления впускного распределительного изменения фаз газораспределения DTC | 0011h | Intake Camshaft Variable Valve Timing Control Function | Fault Type | Description | ABC Type | 78h | Incorrectly Adjusted or Aligned Component Detected | Vbx_clf | 77h | Unable to Move the Component to the Commanded Posi-tion | Vbx_clf | 92h | Component Performance Outside its Expected Range | Vbx_clf | Detection Conditions for Bit 4 (readiness) | 78h | learning of the camshaft wheel enabled: Comparision between [measured angu-lar positions of the intake camshaft wheel active edges] and [values stored in Eeprom] is disable AND no Minitool request | 77h | All learning finished (camshaft wheel and intergral term) AND Engine speed > 2000 rpm AND PWM Bench Mode is disable AND battery voltage > 10 V AND oil temp (or coolant temp) > 70 °C AND Calibration choice (Vrai bool) AND no DTC present linked to VVTC actuator or cam angle sensor. All those conditions has to be completed during a delay: (quickest of both 4 s and 10 s) AND 0,1 s | 92h | All learning finished (camshaft wheel and intergral term) AND Engine speed > 2000 rpm AND PWM Bench Mode is disable AND battery voltage > 10 V AND oil temp (or coolant temp) > 70 °C AND Calibration choice (Vrai bool) AND no DTC present linked to VVTC actuator or cam angle sensor. All those conditions has to be completed during a delay: (quickest of both 4 s and 10 s). | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 78h | Abnormal angular position of an ac-tive edge of the camshaft wheel | < 10s | < 10s | 77h | [VVTC regulation error over max threshold OR abnormal saturation of VVTC actuator command] near low trust position | < 10s | < 10s | 92h | [VVTC regulation error over max threshold (13 °Crk) OR abnormal saturation of VVTC actuator com-mand] AND VVT is NOT near low trust position | < 10s | < 10s | Specific Snapshot | $2007 - Oil temperature - engine | $2010 - Engine status | $2030 - Intake camshaft phaser position setpoint | $2031 - Intake camshaft phaser position | $2033 - Intake camshaft phaser PWM command |
P0016 – Положение распределительного вала - корреляция впускного распределительного положения DTC | 0016h | Camshaft Position – Intake Camshaft Position Correlation | Fault Type | Description | ABC Type | 62h | Two (or More) Input Parameters compared for Plausibil-ity | Vbx_cf | Detection Conditions for Bit 4 (readiness) | 62h | Engine running AND engine speed < C_N_32_MAX_DIAG_REF_CRK_CAM AND no DTC present linked to camshaft and crankshaft sensors | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 62h | Camshaft reference position is outside of the designed range (relative to the engine position from crankshaft) | < 1s | < 1s | Specific Snapshot | $2014 - Camshaft/crankshaft synchronization state | $2016 - Crankshaft synchronization state | $2031 - Intake camshaft phaser position | $2162 - Counter of loose of crankshaft synchronization | $240B - Intake manifold pressure |
P0105 – Датчик абсолютного давления DTC | 0105h | Manifold Absolute Pressure Sensor | Fault Type | Description | ABC Type | 17h | Voltage Above a Specified Range | Sbx_cf | 16h | Voltage Below a Specified Range | Sbx_cf | 29h | Signal Not Plausible | Detection Conditions for Bit 4 (readiness) | 17h | + APC AND DTC 0641h not present | 16h | + APC AND DTC 0641h not present | 29h | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 17h | Manifold pressure sensor volt-age signal > 4,975585938 V | 1000 ms | 2000 ms | 16h | Manifold pressure sensor volt-age signal < 0,04898071289 V | 1000 ms | 2000 ms | 29h | 0 ms | 0 ms | Specific Snapshot | $2401 - Boost pressure | $2422 - Amount of air pumped into cylinder | $24D7 - Manifold pressure value from model | $24E1 - Manifold pressure from sensor | $FD81 - Intake manifold pressure sensor voltage |
P0106 – Функция абсолютного давления DTC | 0106h | Manifold Absolute Pressure Function | Fault Type | Description | ABC Type | 64h | Plausibility Failure | Sbx_cf | 1Ch | Voltage Outside the Expected Range | Sbx_cf | Detection Conditions for Bit 4 (readiness) | 64h | Engine speed > 700 rpm AND DTC 0641h, 060Ah, 061Ah, 0560h, 0606h, 2100h, 0638h NOT present AND (DTC 0106h present OR DTC 095h, 0115h, 0651h, 0443h NOT present) | 1Ch | Stopped engine: DTC 0651h not present Running engine: Engine speed > 700 rpm AND DTC 0641h, 060Ah, 061Ah, 0560h, 0606h, 2100h, 0638h not present | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 64h | Abnormal manifold pressure value (compared to modelized value) | 2000 ms | 5140 ms | 1Ch | Stopped engine: Manifold pressure NOT between 500 hPa & 20000 hPa Running engine: (Manifold pressure < 125 hPa AND Inlet throttle relative position > 10 wu) OR (Manifold pressure > Cxx_sens_map_run_h_thd AND Inlet throttle relative position < 10 wu) | < 2s | < 2s | 400 ms | 11 min | 11 min | 11 min | Specific Snapshot | $240B - Intake manifold pressure | $2422 - Amount of air pumped into cylinder | $243F - Intake manifold temperature | $24D7 - Manifold pressure value from model | $FD81 - Intake manifold pressure sensor voltage |
P0115 –Датчик температуры охлаждающей жидкости двигателя DTC | 0115h | Engine Coolant Temperature Sensor | Fault Type | Description | ABC Type | 17h | Voltage Above a Specified Range | Sbx_cf | 16h | Voltage Below a Specified Range | Sbx_cf | 2Fh | Signal momentarily Implausible or Discontinuous | Vbx_clf | 86h | Circuit Quantity Not Plausible given to Operating Con-ditions | Detection Conditions for Bit 4 (readiness) | 17h | +APC | 16h | +APC | 2Fh | No DTC present linked to coolant temperature sensor | 86h | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 17h | Coolant temperature sensor voltage signal > 4,9609375 V | 1000 ms | 4000 ms | 16h | coolant temperature sensor volt-age signal < 0,05859375 V | 1000 ms | 4000 ms | 2Fh | Abnormal coolant temperature gradient | 8000 ms | 80000 ms | 86h | 0 ms | 0 ms | Specific Snapshot | $2010 - Engine status | $204A - Motor-fans requests | $243F - Intake manifold temperature | $2C04 - Current gear engaged | $2010 - Engine status |
P0120 – Датчик положения дроссельной заслонки DTC | 0120h | Intake Throttle Position Sensor | Fault Type | Description | ABC Type | 29h | Signal Not Plausible | Vbx_clf | Detection Conditions for Bit 4 (readiness) | 29h | DTC 0651h not present | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 29h | Unplausible IT sensor 1 position | 190 ms | 4680 ms | Specific Snapshot | $2021 - Sensors supply voltage 1 | $2415 - Throttle valve position - track 1 | $2416 - Throttle valve position - track 2 |
P0130 – Управляющий датчик кислорода DTC | 0130h | O2 Sensor - Upstream | Fault Type | Description | ABC Type | 09h | No Component Specific SubType | 13h | Circuit Open | Sbx_cf | 11h | Circuit Short to Ground | Sbx_cf | 12h | Circuit Short to Battery | Sbx_cf | 93h | Component Not Operating | 96h | Component Indicating a Failure | 98h | Temperature too High | Detection Conditions for Bit 4 (readiness) | 09h | Vehicle speed > 0 km/h AND Coolant temp > 50 °C AND engine running time > 630 s AND 1500 rpm < engine speed < 4000 rpm AND no variation of engine speed AND no DTC present | 13h | Engine autonomous AND Upstream lambda sensor is hot AND Upstream lambda sensor output voltage between 1395 mV & 1870 mV | 11h | Engine autonomous AND Upstream lambda sensor is hot AND No Injection cut | 12h | [Engine running AND DTC 0135h not present AND Sensor Hot] during 7 s | 93h | 96h | 98h | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 09h | Abnormal duration of min pe-riod duration of lambda sensor | 20000 ms | 20000 ms | 13h | Activation conditions true dur-ing 0,2 s | 5000 ms | 20 ms | 11h | Upstream lambda sensor out-put voltage < 20 mV | 10000 ms | 20 ms | 12h | Upstream lambda sensor out-put voltage > 1870 mV | 10 ms | 20 ms | 93h | 0 ms | 0 ms | 96h | 0 ms | 0 ms | 98h | 0 ms | 0 ms | Specific Snapshot | $240B - Intake manifold pressure | $2422 - Amount of air pumped into cylinder | $2449 - Catalyst exhaust gas upstream oxygen sensor voltage | $244B - Catalyst exhaust gas upstream oxygen resistance heater PWM command | $284E - Richness regulation status |
P0133 – УДК медленный отклик в цепи DTC | 0133h | O2 Sensor Circuit Slow Response | Fault Type | Description | ABC Type | 17h | Voltage Above a Specified Range | 16h | Voltage Below a Specified Range | Detection Conditions for Bit 4 (readiness) | 17h | Time after engine start > 630 s AND 20 kg/h < mass air flow < 150 kg/h AND 1200 rpm < engine speed < 4000 rpm AND vehicle speed > 30 km/h AND en-gine coolant temperature > 80 °C AND Richness double loop activated AND No sensor failure (regarding enable conditions) present | 16h | Time after engine start > 630 s AND 20 kg/h < mass air flow < 150 kg/h AND 1200 rpm < engine speed < 4000 rpm AND vehicle speed > 30 km/h AND en-gine coolant temperature > 80 °C AND Richness double loop activated AND No sensor failure (regarding enable conditions) present | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 17h | Signal amplitude lower than threshold wu | 0 ms | 0 ms | 16h | Signal amplitude lower than threshold wu | 0 ms | 0 ms | Specific Snapshot | $284E - Richness regulation status | $2422 - Amount of air pumped into cylinder | $251D - Internal sensor temperature | $251E - Raw UEGO Air Fuel ratio measurement |
P0135 – Нагреватель УДК DTC | 0135h | O2 Sensor Heater - Upstream | Fault Type | Description | ABC Type | 13h | Circuit Open | 11h | Circuit Short to Ground | 12h | Circuit Short to Battery | 92h | Component Performance Outside its Expected Range | 13h | Circuit Open | Sbx_cf | 11h | Circuit Short to Ground | Sbx_cf | 12h | Circuit Short to Battery | Sbx_cf | Detection Conditions for Bit 4 (readiness) | 13h | Key ON | 11h | Key ON | 12h | key on | 92h | Time after engine start > 100 s AND Ambient temperature > -8 °C AND Exhaust gas temperature < 900 °C | 13h | 10V < battery voltage < 16V AND [[engine autonomous AND O2 sensor heater output is ON] OR at key-on] | 11h | 10V < battery voltage < 16V AND [[when engine autonomous AND O2 sensor heater output becomes ON] OR at key-on] | 12h | 10V < battery voltage < 16V AND [[engine autonomous AND O2 sensor heater output is ON] OR at key-on] | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 13h | Hardware detection of open circuit | 0 ms | 0 ms | 11h | Hardware detection | 0 ms | 0 ms | 12h | Hardware detection | 0 ms | 0 ms | 92h | Number of acquisition windows where the mean value of heater cur-rent is faulty = 3 wu | 0 ms | 0 ms | 13h | Hardware detection | 2000 ms | 4000 ms | 11h | Hardware detection | 2000 ms | 4000 ms | 12h | Hardware detection | 2000 ms | 4000 ms | Specific Snapshot |
P0136 – Диагностический датчик кислорода DTC | 0136h | O2 Sensor - Downstream | Fault Type | Description | ABC Type | 24h | Signal remains High when Transitions are Expected | 23h | Signal remains Low when Transitions are Expected | 13h | Circuit Open | Sbx_cf | 11h | Circuit Short to Ground | Sbx_cf | 12h | Circuit Short to Battery | Sbx_cf | Detection Conditions for Bit 4 (readiness) | 24h | The abnormal voltage on the lean side diagnosis is done | 23h | 13h | [Downstream sensor heating activated almost one time during the current driving cycle (engine running time > 5min at idle speed) AND engine autonomous AND DTC 0141h not present] during 5 s | 11h | Engine running AND out of injection cut-off phase AND DTC 0105h, 0095h, 0115h not present | 12h | [Engine running AND Accelerator pedal pressed AND DTC 0141h not present AND Downstream sensor heating activated and warmed up after 5min] AND during 5 s | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 24h | 0 ms | 0 ms | 23h | 0 ms | 0 ms | 13h | Lambda sensor signal > 1300 mV after more than 10s of injection cut-off | 10 s | 10 s | 11h | Rear Oxygen Sensor signal < 20 mV | < 30s | < 2s | 12h | Rear Oxygen Sensor signal > 1870 mV | < 2s | < 2s | Specific Snapshot | $240B - Intake manifold pressure | $2422 - Amount of air pumped into cylinder | $244A - Catalyst exhaust gas downstream oxygen sensor voltage | $244C - Catalyst exhaust gas downstream oxygen resistance heater PWM command | $2449 - Catalyst exhaust gas upstream oxygen sensor voltage |
P0140 – ДДК активность цепи DTC | 0140h | O2 Sensor Circuit Activity | Fault Type | Description | ABC Type | 29h | Signal Not Plausible | Detection Conditions for Bit 4 (readiness) | 29h | The degradation response diagnosis is done | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 29h | 0 ms | 0 ms | Specific Snapshot | $244A - Catalyst exhaust gas downstream oxygen sensor voltage | $2449 - Catalyst exhaust gas upstream oxygen sensor voltage | $24C1 - Time expected to switch on the heating of the downstream sensor | $284E - Richness regulation status | $2010 - Engine status |
P0141 – Нагреватель ДДК DTC | 0141h | O2 Sensor Heater - Downstream | Fault Type | Description | ABC Type | 92h | Component Performance Outside its Expected Range | 13h | Circuit Open | Sbx_cf | 11h | Circuit Short to Ground | Sbx_cf | 12h | Circuit Short to Battery | Sbx_cf | Detection Conditions for Bit 4 (readiness) | 92h | Coolant temperature > -7 °C | 13h | 10V < battery voltage < 16V AND [[engine autonomous AND O2 sensor heater output is ON] OR at key-on] | 11h | 10V < battery voltage < 16V AND [[when engine autonomous AND O2 sensor heater output becomes ON] OR at key-on] | 12h | 10V < battery voltage < 16V AND [[engine autonomous AND O2 sensor heater output is ON] OR at key-on] | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 92h | Number of acquisition windows where the mean value of heater current is faulty = 45 wu | 2 ms | 2 ms | 13h | Hardware detection | 2000 ms | 2000 ms | 11h | Hardware detection | 2000 ms | 2000 ms | 12h | Hardware detection | 2000 ms | 2000 ms | Specific Snapshot | $240B - Intake manifold pressure | $244A - Catalyst exhaust gas downstream oxygen sensor voltage | $244C - Catalyst exhaust gas downstream oxygen resistance heater PWM command | $2506 - Progress in the heater strategy | $284E - Richness regulation status |
P0170 – Топливо DTC | 0170h | Fuel Trim | Fault Type | Description | ABC Type | 09h | No Component Specific SubType | Vbx_cf | Detection Conditions for Bit 4 (readiness) | 09h | 950 rpm < Engine speed < 6000 rpm AND engine running for more than 0 s AND no DTC present AND No blow-by detected AND Minimum fuel lamp not switched on | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 09h | Mean richness deviation exceed-ing threshold (+/- 17% of Rich-ness = 1, when coolant tempera-ture > 60 °C) | 60s | 60s | Specific Snapshot | $2449 - Catalyst exhaust gas upstream oxygen sensor voltage | $2010 - Engine status | $2872 - Corrective factor depending on exotic fuel quantity. For injection time | $2873 - Corrected average ALFACL for memorized fuel system diagnostic | $2874 - Misfire counter |
P0201 – Цепь форсунки – цилиндр 1 DTC | 0201h | Injector Circuit – Cylinder 1 | Fault Type | Description | ABC Type | 13h | Circuit Open | Vbx_clf | 11h | Circuit Short to Ground | Vbx_clf | 12h | Circuit Short to Battery | Vbx_clf | Detection Conditions for Bit 4 (readiness) | 13h | +APC | 11h | +APC | 12h | +APC | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 13h | Hardware detection | < 1500ms | < 2500ms | 11h | Hardware detection | < 1500ms | < 2500ms | 12h | Hardware detection | < 1500ms | < 2500ms | Specific Snapshot |
P0202 – Цепь форсунки – цилиндр 2 DTC | 0202h | Injector Circuit – Cylinder 2 | Fault Type | Description | ABC Type | 13h | Circuit Open | Vbx_clf | 11h | Circuit Short to Ground | Vbx_clf | 12h | Circuit Short to Battery | Vbx_clf | Detection Conditions for Bit 4 (readiness) | 13h | +APC | 11h | +APC | 12h | +APC | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 13h | Hardware detection | < 1500ms | < 2500ms | 11h | Hardware detection | < 1500ms | < 2500ms | 12h | Hardware detection | < 1500ms | < 2500ms | Specific Snapshot |
P0203 – Цепь форсунки – цилиндр 3 DTC | 0203h | Injector Circuit – Cylinder 3 | Fault Type | Description | ABC Type | 13h | Circuit Open | Vbx_clf | 11h | Circuit Short to Ground | Vbx_clf | 12h | Circuit Short to Battery | Vbx_clf | Detection Conditions for Bit 4 (readiness) | 13h | +APC | 11h | +APC | 12h | +APC | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 13h | Hardware detection | < 1500ms | < 2500ms | 11h | Hardware detection | < 1500ms | < 2500ms | 12h | Hardware detection | < 1500ms | < 2500ms | Specific Snapshot |
P0204 – Цепь форсунки – цилиндр 4 DTC | 0204h | Injector Circuit – Cylinder 4 | Fault Type | Description | ABC Type | 13h | Circuit Open | Vbx_clf | 11h | Circuit Short to Ground | Vbx_clf | 12h | Circuit Short to Battery | Vbx_clf | Detection Conditions for Bit 4 (readiness) | 13h | +APC | 11h | +APC | 12h | +APC | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 13h | Hardware detection | < 1500ms | < 2500ms | 11h | Hardware detection | < 1500ms | < 2500ms | 12h | Hardware detection | < 1500ms | < 2500ms | Specific Snapshot |
P0217 – Температура охлаждающей жидкости двигателя DTC | 0217h | Engine Coolant Temperature | Fault Type | Description | ABC Type | 98h | Temperature too High | Detection Conditions for Bit 4 (readiness) | 98h | Key ON | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 98h | Coolant temperature > 115 °C | 1000 ms | 1000 ms | Specific Snapshot | $204A - Motor-fans requests | $243F - Intake manifold temperature | $2C04 - Current gear engaged |
P0220 – Датчик положения дроссельной заслонки – трек 2 DTC | 0220h | Intake Throttle Position Sensor - Track 2 | Fault Type | Description | ABC Type | 29h | Signal Not Plausible | Vbx_clf | Detection Conditions for Bit 4 (readiness) | 29h | DTC 0651h not present | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 29h | Unplausible IT sensor 2 position (sensor 2 position >96 % Vsens OR sensor 2 position) | 190 ms | 4680 ms | Specific Snapshot | $2021 - Sensors supply voltage 1 | $2415 - Throttle valve position - track 1 | $2416 - Throttle valve position - track 2 |
P0225 – Датчик положения педали акселератора – трек 1 DTC | 0225h | Accelerator Pedal Position Sensor - Track 1 | Fault Type | Description | ABC Type | 17h | Voltage Above a Specified Range | Sbx_cf | 16h | Voltage Below a Specified Range | Sbx_cf | Detection Conditions for Bit 4 (readiness) | 17h | DTC 0651h not present | 16h | DTC 0651h not present | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 17h | accelerator pedal sensor 1 output voltage > 0,964809384164222 Uref ratio AND DTC 0651h not present | 250 ms | 1000 ms | 16h | accelerator pedal sensor 1 output voltage < 7,33137829912023E-02 Uref ratio AND DTC 0651h not present | 250 ms | 1000 ms | Specific Snapshot | $200B - Accelerator pedal voltage - track 1 | $200C - Accelerator pedal voltage - track 2 | $2021 - Sensors supply voltage 1 | $2022 - Sensors supply voltage 2 | $2023 - Sensors supply voltage 3 |
P0226 – Датчик положения педали акселератора DTC | 0226h | Accelerator Pedal Position Sensor | Fault Type | Description | ABC Type | 64h | Plausibility Failure | Sbx_cf | F1h | Safety Case 1 | Sbx_cf | F2h | Safety Case 2 | Sbx_cf | F3h | Multiple Failure | Sbx_cf | Detection Conditions for Bit 4 (readiness) | 64h | [No accelerator pedal track 1 or 2 signal detected failure (high or low) AND no failure on acc. pedal track 1 or 2 power supply] OR DTC 0226h present | F1h | - accelerator pedal variation < 0,300097751710654 Uref ratio/s - accel pedal po-sition > 0,204301075268817 Uref ratio - vehicle speed > 0 km/h - no accelerator pedal detected failure, - no AYC, ASR or MSR current request if configuration bit is not set, - accelerator pedal sensor information not invalid. - engine speed > 608 rpm. - no braking setpoint from Adaptive Cruise Control system (only for applications with ACC) if configuration bit is not set. - brake pedal pressed | F2h | - accelerator pedal variation < 0,300097751710654 Uref ratio/s - accel pedal po-sition > 0,204301075268817 Uref ratio - vehicle speed > 0 km/h - no accelerator pedal detected failure, - no AYC, ASR or MSR current request if configuration bit is not set, - accelerator pedal sensor information not invalid. - engine speed > 608 rpm. - no braking setpoint from Adaptive Cruise Control system (only for applications with ACC) ifconfiguration bit is not set. - brake pedal pressed | F3h | Always | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 64h | Difference between accelerator pedal track 1 & 2 position > [6%..8%] Uref ratio | 400 ms | 1600 ms | F1h | No accelerator pedal position var-iation during at least cxx_acel_pdl_dly1 + cxx_acel_pdl_dly2 AND brake pedal pressed during cxx_acel_pdl_dly2 | 1200 ms | 20 ms | F2h | No accelerator pedal position var-iation during at least cxx_acel_pdl_dly1 + cxx_acel_pdl_dly2 AND brake pedal pressed during cxx_acel_pdl_dly2 | 30000 ms | 0 ms | F3h | [(DTC 2120h OR DTC 0641h) AND DTC 0226h] OR [(DTC 0225h OR DTC 0651h) AND DTC 0226h] OR [(DTC 2120 OR 0641h) AND (DTC 0225h OR DTC 0651h)] | 250 ms | 10000 ms | Specific Snapshot | $200B - Accelerator pedal voltage - track 1 | $200C - Accelerator pedal voltage - track 2 | $2021 - Sensors supply voltage 1 | $2022 - Sensors supply voltage 2 | $2036 - Counter of inconsistencies between accelerator pedal and brake |
P025A – Модуль цепи управления бензонасосом DTC | 025Ah | Fuel Pump Module Control Circuit | Fault Type | Description | ABC Type | 13h | Circuit Open | 11h | Circuit Short to Ground | 12h | Circuit Short to Battery | Detection Conditions for Bit 4 (readiness) | 13h | +APC AND 6 < battery voltage < 12 | 11h | +APC AND 6 < battery voltage < 12 | 12h | +APC AND 6 < battery voltage < 12 | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 13h | Hardware detection of Open Circuit | < 2s | < 2s | 11h | 1000 ms | 3000 ms | 12h | < 2s | < 2s | Specific Snapshot | $2889 - Raw fuel pressure from sensor | $2887 - PWM of fuel pump actuator | $288A - Default type sent by PCU |
P0300 – Обнаружены случайные / множественные пропуски воспламенения DTC | 0300h | Random/Multiple Cylinder Misfire Detected | Fault Type | Description | ABC Type | F8h | Catalyst Destructive | Vbx_cf | 66h | More Transitions than a Specified Number | Vbx_cf | Detection Conditions for Bit 4 (readiness) | F8h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | 66h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | F8h | Abnormal number of torque diminutions BUT no cylinder identified | 20s | 20s | 66h | Abnormal torque diminution BUT no cylinder identified | 10 min | 10 min | Specific Snapshot | $281B - Fuel low level | $2841 - Misfire counter - cylinder 1 | $2842 - Misfire counter - cylinder 2 | $2843 - Misfire counter - cylinder 3 | $2844 - Misfire counter - cylinder 4 |
P0301 – Обнаружены пропуски воспламенения – цилиндр 1 DTC | 0301h | Cylinder 1 Misfire Detected | Fault Type | Description | ABC Type | F8h | Catalyst Destructive | Vbx_cf | 66h | More Transitions than a Specified Number | Vbx_cf | Detection Conditions for Bit 4 (readiness) | F8h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | 66h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | F8h | Abnormal number of torque dimi-nutions on cylinder 1 | 20s | 20s | 66h | Abnormal torque diminution on cylinder 1 | 10 min | 10 min | Specific Snapshot | $281B - Fuel low level | $2841 - Misfire counter - cylinder 1 | $2842 - Misfire counter - cylinder 2 | $2843 - Misfire counter - cylinder 3 | $2844 - Misfire counter - cylinder 4 |
P0302 – Обнаружены пропуски воспламенения – цилиндр 2 DTC | 0302h | Cylinder 2 Misfire Detected | Fault Type | Description | ABC Type | F8h | Catalyst Destructive | Vbx_cf | 66h | More Transitions than a Specified Number | Vbx_cf | Detection Conditions for Bit 4 (readiness) | F8h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | 66h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | F8h | Abnormal number of torque dimi-nutions on cylinder 2 | 20s | 20s | 66h | Abnormal torque diminution on cylinder 2 | 10 min | 10 min | Specific Snapshot | $281B - Fuel low level | $2841 - Misfire counter - cylinder 1 | $2842 - Misfire counter - cylinder 2 | $2843 - Misfire counter - cylinder 3 | $2844 - Misfire counter - cylinder 4 |
P0303 – Обнаружены пропуски воспламенения – цилиндр 3 DTC | 0303h | Cylinder 3 Misfire Detected | Fault Type | Description | ABC Type | F8h | Catalyst Destructive | Vbx_cf | 66h | More Transitions than a Specified Number | Vbx_cf | Detection Conditions for Bit 4 (readiness) | F8h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | 66h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | F8h | Abnormal number of torque dimi-nutions on cylinder 3 | 20s | 20s | 66h | Abnormal torque diminution on cylinder 3 | 10 min | 10 min | Specific Snapshot | $281B - Fuel low level | $2841 - Misfire counter - cylinder 1 | $2842 - Misfire counter - cylinder 2 | $2843 - Misfire counter - cylinder 3 | $2844 - Misfire counter - cylinder 4 |
P0304 – Обнаружены пропуски воспламенения – цилиндр 4 DTC | 0304h | Cylinder 4 Misfire Detected | Fault Type | Description | ABC Type | F8h | Catalyst Destructive | Vbx_cf | 66h | More Transitions than a Specified Number | Vbx_cf | Detection Conditions for Bit 4 (readiness) | F8h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | 66h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | F8h | Abnormal number of torque dimi-nutions on cylinder 4 | 20s | 20s | 66h | Abnormal torque diminution on cylinder 4 | 10 min | 10 min | Specific Snapshot | $281B - Fuel low level | $2841 - Misfire counter - cylinder 1 | $2842 - Misfire counter - cylinder 2 | $2843 - Misfire counter - cylinder 3 | $2844 - Misfire counter - cylinder 4 |
P0313 – Обнаружены пропуски воспламенения – отключена топливоподача DTC | 0313h | Misfire Detected with Low Fuel | Fault Type | Description | ABC Type | F8h | Catalyst Destructive | Vbx_cf | 66h | More Transitions than a Specified Number | Vbx_cf | Detection Conditions for Bit 4 (readiness) | F8h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | 66h | 550 rpm < engine speed < 4500 rpm AND coolant temperature > -8 ºC AND no DTC present linked to injection system | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | F8h | Abnormal number of torque dimi-nutions on one or more cylinders with low fuel level in tank | 20s | 20s | 66h | Abnormal torque diminution on one or more cylinders with low fuel level in tank | 10 min | 10 min | Specific Snapshot | $281B - Fuel low level | $2841 - Misfire counter - cylinder 1 | $2842 - Misfire counter - cylinder 2 | $2843 - Misfire counter - cylinder 3 | $2844 - Misfire counter - cylinder 4 |
P0315 - Система положения коленчатого вала вариатора не обучена DTC | 0315h | Crankshaft Position System Variation Not Learned | Fault Type | Description | ABC Type | 09h | No Component Specific SubType | Sbx_cf | Detection Conditions for Bit 4 (readiness) | 09h | After injection cut-off between 3000 Rpm & 3500 Rpm, during 100 TDC (for crankshaft position system variation learning) | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 09h | Abnormal value for crankshaft tar-get variation learning | 100 TDC | 100 TDC | Specific Snapshot | $2156 - TLZ - Last achieved adaptive value | $215D - TLZ - TLZ adaptive correction |
P0325 – Датчик детонации DTC | 0325h | Knock Sensor | Fault Type | Description | ABC Type | 1Ch | Voltage Outside the Expected Range | Sbx_cf | Detection Conditions for Bit 4 (readiness) | 1Ch | Engine running AND Coolant temperature > 120 °C AND Mass Airflow > 223 mg/stk AND engine speed > 1504 RPM | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 1Ch | Abnormal Knock sensor signal (too low) | 2600 ms | 2600 ms | Specific Snapshot | $2847 - Knock counter detection - cylinder 1 | $2848 - Knock counter detection - cylinder 2 | $2849 - Knock counter detection - cylinder 3 | $284A - Knock counter detection - cylinder 4 | $284D - Mean knock noise |
P0335 – Датчик положения коленчатого вала DTC | 0335h | Crankshaft Position Sensor | Fault Type | Description | ABC Type | 64h | Plausibility Failure | Vbx_clf | 62h | Two (or More) Input Parameters compared for Plausibility | Vbx_clf | 38h | Incorrect Number of Cycles in a Given Time Period | Vbx_clf | 31h | Signal Not Detected | Vbx_clf | Detection Conditions for Bit 4 (readiness) | 64h | Engine running AND no DTC present linked to camshaft and crankshaft sensors | 62h | Engine speed > C_N_32_MAX_DIAG_CRK_TOOTH AND no DTC present linked to camshaft and crankshaft sensors | 38h | Engine running AND no DTC present linked to crankshaft or camshaft sensors | 31h | Engine running AND no DTC present linked to camshaft and crankshaft sensors | Detection Conditions for Bit 0 (test failed) | Detection timing | Resorption Timing | 64h | Reference gap not detected at cor-rect position +/- > 2 teeth | < 1s | < 1s | 62h | Abnormal number of teeth per crankshaft revolution, until +/- 2 teeth | < 1s | < 1s | 38h | Noisy crankshaft signal | < 1s | < 1s | 31h | Crankshaft sensor signal is missing | < 1s | at next driving cycle | Specific Snapshot | $2010 - Engine status | $2014 - Camshaft/crankshaft synchronization state | $2016 - Crankshaft synchronization state | $2161 - Crankshaft signal | $2162 - Counter of loose of crankshaft synchronization |
ДВИГАТЕЛЯ Н4М |
Описание курса
| ДВИГАТЕЛЬ H4Mk
|